Tuesday, November 14, 2017

PIC Frequency Counter With Morse Output

It's a little strange to blog about a project that's mostly software, but even if I don't explore the software design in depth I can at least describe the resulting instrument.
For hams who program MCUs, a frequency counter seems to be one of several obligatory projects, with others being a keyer and a controller for a DDS or PLL type synthesizer. So I wanted to get in my frequency counter project.
Counters such as this one have been around for a while, often integrated into radios with analog VFOs. With the tap of a button, you hear the frequency accurately announced in Morse and thus the need for a calibrated dial is avoided.
I said "With Morse Output" but it's common to refer to the device function as AFA, for Audible Frequency Annunciation.
Before I ramble much more, let me list the features of my counter. Every programmer likes to add a wrinkle or two to previous implementations and I've added one or two:


Features
One button control to initiate count or menu actions
User programming of superhet IF frequency offset
Selectable 1 Hz or 100 Hz resolution
Option to suppress higher digits for faster readings
Can be built SMT or through hole
Small size - I used a RS proto board 1.75 x 2.75 inch
Setup saved on EEPROM and recalled on power-up
Three selectable Morse annunciation speeds
Selectable audible marker for each 1 kHz change while tuning

Specifications (approximate)
Accuracy:  Depending on the time base, can be as good as 1 Hz
Resolution: Selectable to 1 Hz or 100 Hz
Response time: 1 s for 1 Hz resolution and 10 ms for 100 Hz
Sensitivity: 35 mVpp to 180 mV through 6 meters
Idling current draw at 12 V input is 11 mA
My prototype SMT version will read to just over 140 MHz
Minimum frequency is about 50 kHz with input capacitor shown

Some hardware notes and schematic
I'd switched from PICs to AVR MCUs a few years ago but the PIC is unique in having a prescaler that can count really fast - independent of the chip's clock. So I went back to the 16F683 8-pin PIC for this project.
I looked at several other designs although I didn't have their source code to guide me. Some use Microchip's AN592 app note as a starting point, but its accuracy can degrade to 1 kHz or worse at higher frequencies. I liked the Stinger Singer counter sold by the Arizona SQRPions group and designed by Dan Tayloe. The use of a 74HC00 AND-gate package allowed precise gating of the input stream and also gating out and counting the remainder stuck in the prescaler, which can't be read directly.


Sorry it's fuzzy. I'll provide a link to a better schematic.

I built my DIP version on a Radio Shack 276-150 prototype board. Radio Shack is gone but I found some at B.G Micro. I also built a SMT version on a board I made using the toner transfer technique. You could omit the programming header if you have a pre-programmed chip.

Want to try it?
I've added a link to the HEX code. You can burn it to a PIC with a PICkit-2 or PICkit-3. Or I could program a PIC for you and mail it in the USA. Say $4 to buybye@suddenlink.net which is my PayPal address. Or four ones to my QRZ address. First make sure I'm still alive and capable of fulfilling the request by emailing me at kennnick@gmail.com.
I've also linked a manual below, with a lot more info on building and operating the counter.

Possible improvements
I like the feature I added to give an audible "tick" marker with every kHz of change. But it introduced an artifact. When this feature is ON, the counter must read the frequency continuously and the pin that drives the speaker is also used in counting logic. This results in a low "puttering" sound from the speaker that's almost but not quite inaudible. Of course you can turn it OFF if it's a bother. One fix I've considered is to use a separate crystal oscillator with a transistor for the timebase. That would free up one PIC pin to dedicate to the speaker. Another fix would be to use a higher pin count PIC. But a 14 or 18 pin PIC would make the counter so much larger. I could justify it by integrating a keyer function into the chip as others have done. That would make it worthwhile.

Files



73,
Nick, WA5BDU

2 comments:

Kenn Goodson said...

Hey Nick! I found a small typo: the article refers to a 16f683 why the schematic shows a 12f683. I'm going to try out your project this weekend. I was looking for an alternative to the FREQ-MITE and this looks pretty intriguing.

Cheers and 73,
Kenn
KA5KXW

Nick Kennedy said...

I need to check my comments more often! Thanks for spotting that error, Kenn. Of course the correct part number is 12F683.
I received an email yesterday from a JA who reported that he had built the AFA and was having good luck with it. I was pleased to hear that.

73,

Nick, WA5BDU